Vape Tank Wont Screw Onto Battery Again

Huckleberried

Huckleberried

VU Donator

Diamond Correspondent

Member For 5 Years

VU Patreon

  • #ii

Does it give you lot a reading for your coil? Have you tried another tank?

JERUS

JERUS

Aureate Correspondent

Member For four Years

Member For 3 Years

Member For ii Years

Fellow member For 1 Twelvemonth

  • #iii

So is it going into the hole and just non grabbing? That sounds stripped, or is it not grabbing the top of the threading so it'southward never getting into the hole? If then bank check the ends of the threading possibly one office got tweaked so it's never linking upward correctly?

Final, I don't have either of those devices merely is it possible that what the threading is connected to was detached and is spinning?

Vapin4Joy

Vapin4Joy

Diamond Correspondent

Member For iv Years

  • #4

Sounds like the threads of the 510 are going, try pushing your tank while screwing it in and run into if it grabs the threads at the lesser of the 510. If yes become yourself a heat sink at your local vape shop and push and screw that in, yous take just installed new threads.

James

James

Statuary Contributor

Member For four Years

Member For 3 Years

ECF Refugee

Vapin4Joy

Vapin4Joy

Diamond Contributor

Member For 4 Years

smacksy

smacksy

Platinum Contributor

Member For four Years

  • #7

Heya everyone :)
I am having a problem and am hoping someone here can aid me. I have the evic vtc mini, and today I took the tank off to refill it and at present information technology wont spiral back on the mod (is that the correct term?) The threads are fine and I can't see annihilation wrong but it wont spiral on. Information technology merely spins and spins and never grabs. I have refilled the tank dozens of times and this has never happened earlier. Please help :)

Rob

Can yous post a few pics perhaps?
It might assistance us to help you amend..

Sent from my XT1080 using Tapatalk

Jasonk1229

  • #8

mine did this too the connection is cleaved i haven't attempted a repair i only bought another
you can force it to stay on jam a toothpick and turn it simply it's just temporary

James

James

Bronze Contributor

Member For 4 Years

Member For three Years

ECF Refugee

  • #nine

If the 510 on summit of the mod is striped it tin can be replaced . If the threads on the tank are dammaged , if you lot droped the tank ? , thay may be fixed with a small triangle shaped file . Practice non force them . You lot will just dammage them both . With a skilful await at the threads on the tank tin yous tell if the 1st thread is flattend in to the second thread ?

pulsevape

Diamond Contributor

Fellow member For 4 Years

  • #10

Hit it with a large fucking hammer....always worked on my TV.

Jasonk1229

  • #xi

its not a matter of it beung stripped it was the leap in the 510 no thought where to go a replacement i took apart the modern and even checked out a youtube about it.

if anyonr has any links to parts would appreciate it

wally

wally

Aureate Contributor

Fellow member For 4 Years

ECF Refugee

  • #12

I had 1 of these the 510 fit the tanks looser than my other mods which told me the tolerance is wider than about which leads to threads wearing out faster. Nada can be done about it unless you install a new 510 or apply an older 510 off another unit. I finally sold it and just used my I stick lx which always works flawlessly. Information technology does non have updating but who needs information technology if it is congenital right in the kickoff place. It is non hard to fix these if you lot can solder if you can't you could prolly find someone who can. Buying another one will but give you the aforementioned results unless they start using stainless steal for the 510 information technology has stronger steal and will hold upwards. The heat sink idea is skilful if it will tighten on good enough to hold but don't remove it remove the tank..

Angrygod50

Angrygod50

Aureate Contributor

Member For iv Years

Member For iii Years

Member For 2 Years

  • #15

Looks similar yous pulled the threaded insert out of the mod. New 510 like a Fatty Daddy if there's room or a new mod.

fulleryoughter.blogspot.com

Source: https://vapingunderground.com/threads/help-my-tank-wont-screw-back-on.183215/

0 Response to "Vape Tank Wont Screw Onto Battery Again"

Post a Comment

Iklan Atas Artikel

Iklan Tengah Artikel 1

Iklan Tengah Artikel 2

Iklan Bawah Artikel